please dont rip this site

Arduino Code for ENC2 / AS5047P SPI

Thank you Doug!

#include <SPI.h>
unsigned int reading = 0;

// AS4047P Registers
#define AS5047P_select_pin 10

/** volatile **/
#define NOP 0x0000
#define ERRFL 0x0001
#define PROG   0x0003
#define DIAAGC 0x3FFC
#define CORDICMAG 0x3FFD
#define ANGLEUNC  0x3FFE
#define ANGLECOM  0x3FFF

/** non-volatile **/
#define ZPOSM 0x0016
#define ZPOSL 0x0017
#define SETTINGS1 0x0018
#define SETTINGS2 0x0019

#define RD  0x40    // bit 14 "1" is Read + parity even
#define WR  0x3F    //bit 14 ="0" is Write

//Op Arduino: D10 CS, D11 MOSI, D12 MISO, D13 SCK
//SPISettings settings(2000000, MSBFIRST, SPI_MODE1); 
SPISettings settings(SPI_CLOCK_DIV4, MSBFIRST, SPI_MODE1); 

void setup() {
  pinMode(AS5047P_select_pin, OUTPUT);

  SPI.begin();
  SPI.setDataMode(SPI_MODE1); // properties chip
  SPI.setBitOrder(MSBFIRST);  //properties chip

  Serial.begin(115200);  // start serial for output
  Serial.println(" AS5047P:");

  AS5047P_Write( AS5047P_select_pin , SETTINGS1, 0x0001); //DJL was 0x0004);
  AS5047P_Write( AS5047P_select_pin , SETTINGS2, 0x0000);
  AS5047P_Write( AS5047P_select_pin , ZPOSM, 0x0000); // is it really possible to initially set angle at 0 degrees??
  AS5047P_Write( AS5047P_select_pin , ZPOSL, 0x0000);
}

void loop()
{
  DumpRegisterValues();
  Serial.println();
  delay(200);
}

void DumpRegisterValues()
{
  Serial.print("NOP: "); Serial.println(AS5047P_Read( AS5047P_select_pin, NOP) & 0x3FFF, BIN); // strip bit 14..15
  Serial.print("ERRFL: "); Serial.println(AS5047P_Read( AS5047P_select_pin, ERRFL) & 0x3FFF, BIN); // strip bit 14..15
  Serial.print("PROG: "); Serial.println(AS5047P_Read( AS5047P_select_pin, PROG) & 0x3FFF, BIN); // strip bit 14..15
  Serial.print("DIAAGC: "); Serial.println(AS5047P_Read( AS5047P_select_pin, DIAAGC) & 0x3FFF, BIN); // strip bit 14..15
  
  Serial.print("CORDICMAG: "); Serial.println(AS5047P_Read( AS5047P_select_pin, CORDICMAG) & 0x3FFF, DEC); // strip bit 14..15
  Serial.print("ANGLEUNC: "); Serial.println(AS5047P_Read( AS5047P_select_pin, ANGLEUNC) & 0x3FFF, DEC); // strip bit 14..15
  Serial.print("ANGLECOM: "); Serial.println(AS5047P_Read( AS5047P_select_pin, ANGLECOM) & 0x3FFF, DEC); // strip bit 14..15

  Serial.print("ZPOSM: "); Serial.println(AS5047P_Read( AS5047P_select_pin, ZPOSM) & 0x3FFF, BIN); // strip bit 14..15
  Serial.print("ZPOSL: "); Serial.println(AS5047P_Read( AS5047P_select_pin, ZPOSL) & 0x3FFF, BIN); // strip bit 14..15
  Serial.print("SETTINGS1: "); Serial.println(AS5047P_Read( AS5047P_select_pin, SETTINGS1) & 0x3FFF, BIN); // strip bit 14..15
  Serial.print("SETTINGS2: "); Serial.println(AS5047P_Read( AS5047P_select_pin, SETTINGS2) & 0x3FFF, BIN); // strip bit 14..15
}

// ************************Write to AS5047P **************************
void AS5047P_Write( int SSPin, int address, int value)
{
  // take the SS pin low to select the chip:
  SPI.beginTransaction(settings);
  digitalWrite(SSPin, LOW);
  
  Serial.println(value, HEX);
  
  //  send in the address via SPI:
  
  byte v_l = address & 0x00FF;
  byte v_h = (unsigned int)(address & 0x3F00) >> 8;
  
  if (parity(address & 0x3F) == 1) v_h = v_h | 0x80; // set parity bit
  //v_h = v_h & (WR | 0x80);  // its  a write command and don't change the parity bit (0x80)
  
  Serial.print( " parity:  "); Serial.println(parity(address & 0x3F));
  Serial.print(v_h, HEX); Serial.print(" A ");  Serial.println(v_l, HEX);
  
  SPI.transfer(v_h);
  SPI.transfer(v_l);
  
  digitalWrite(SSPin, HIGH);
  SPI.endTransaction();
  
  delay(2);
  
  SPI.beginTransaction(settings);
  digitalWrite(SSPin, LOW);
  
  //  send value via SPI:
  
  v_l = value & 0x00FF;
  v_h = (unsigned int)(value & 0x3F00) >> 8;
  
  if (parity(value & 0x3F) == 1) v_h = v_h | 0x80; // set parity bit
  //v_h = v_h & (WR | 0x80); // its a write command and don't change the parity bit (0x80)
  
  Serial.print(v_h, HEX); Serial.print(" D ");  Serial.println(v_l, HEX);
  
  SPI.transfer(v_h);
  SPI.transfer(v_l);
  
  // take the SS pin high to de-select the chip:
  digitalWrite(SSPin, HIGH);
  SPI.endTransaction();
}

//*******************Read from AS5047P ********************************
unsigned int AS5047P_Read( int SSPin, unsigned int address)
{
  unsigned int result = 0;   // result to return
  
  byte res_h = 0;
  byte res_l = 0;
  
  // take the SS pin low to select the chip:
  SPI.beginTransaction(settings);
  digitalWrite(SSPin, LOW);
  
  //  send in the address and value via SPI:
  byte v_l = address & 0x00FF;
  byte v_h = (unsigned int)(address & 0x3F00) >> 8;
  
  if (parity(address | (RD << 8)) == 1) v_h = v_h | 0x80; // set parity bit
  
  v_h = v_h | RD; // its  a read command
  
  // Serial.print( " parity:  ");Serial.println(parity(address | (RD <<8)));
  // Serial.print(v_h, HEX); Serial.print(" A ");  Serial.print(v_l, HEX);  Serial.print(" >> ");
  
  res_h = SPI.transfer(v_h);
  res_l = SPI.transfer(v_l);
  
  digitalWrite(SSPin, HIGH);
  SPI.endTransaction();
  
  delay(2);

  SPI.beginTransaction(settings);
  digitalWrite(SSPin, LOW);
  
  //if (parity(0x00 | (RD <<8))==1) res_h = res_h | 0x80;  // set parity bit
  //res_h = res_h | RD;
  
  res_h = (SPI.transfer(0x00));
  res_l = SPI.transfer(0x00);
  
  res_h = res_h & 0x3F;  // filter bits outside data
  
  //Serial.print(res_h, HEX);   Serial.print(" R  ");  Serial.print(res_l, HEX);   Serial.print("  ");
  
  digitalWrite(SSPin, HIGH);
  SPI.endTransaction();
  
  return (result = (res_h << 8) | res_l);
}

//*******************check parity ******************************************
int parity(unsigned int x) {
  int parity = 0;
  while (x > 0) {
    parity = (parity + (x & 1)) % 2;
    x >>= 1;
  }
  return (parity);
}



file: /Techref/io/sensor/pos/enc/ENC2-47P-Arduino.htm, 6KB, , updated: 2017/6/11 19:17, local time: 2024/3/28 07:42,
TOP NEW HELP FIND: 
3.237.65.102:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://www.ecomorder.com/techref/io/sensor/pos/enc/ENC2-47P-Arduino.htm"> Arduino Code for ENC2 / AS5047P SPI</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to ecomorder.com!

 

Welcome to www.ecomorder.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .